Workshop
Start a discussion

Topics with Label: Tools and Equipment

ProjectPete
Valued Contributor
4 replies

I'm planning a workbench/space in the garage of my new home. I have about 3.7 x 0.8m space to work with in the 'Store'. I also have raised 31 course c ...

Tara86
Established Contributor
20 replies

Hi everyone - as my love and interest in DIY continues to grow I found I needed an adequate area to accommodate this. I needed decent storage and a po ...

Bizebod
Junior Contributor
18 replies

I am looking for an inexpensive, safe and useful table saw to make my little projects both easier to repeat and complete. i didn't want to spend more ...

ProjectPete
Valued Contributor
36 replies

Hi guys, I've got a decent range of tools including both battery and corded models. I'm just chasing people's feedback on which tools they have in whi ...

JustJim
Budding Contributor
7 replies

I'm Jim and I'm new here. Very new. First posting new! I'm retired and keen to get back into woodworking. I recently bought a house in Warrn ...

Dallas_Mc
Budding Contributor
11 replies

Hi all, I'd like to share a project that I'd been thinking about doing for ages, but always found an excuse not to. I was either too busy or too la ...

Kiwifr33
Established Contributor
12 replies

Legs and rails. Rails are dovetailed / lapped flush with the legs. Top left is the first half of the laminated top. Everything is recycled. Cuttin ...

Kiwifr33
Established Contributor
21 replies

Some people go away for their holidays... and then there’s me, who takes four weeks leave to build shed.There was sort of a plan - a couple of drawing ...

Vadar
Occasional Browser
4 replies

what is the best tool to cut perspex?

Tara86
Established Contributor
10 replies

Hey Everyone - hoping I could get some advice on which would be best suited (also cost friendly) for cleaning up and also decreasing the amount of dus ...

Monument
Budding Contributor
1 reply

Back in May in response to a post by Tara86 and an amazing example of a workspace I posted a photo (see the 1st photo in this post) of my work area in ...

Henno
Established Contributor
9 replies

Hi guys, Have a couple of small projects coming up which will require either some small nailing (35mm) but plenty of them. Not sure if I should fork ...

r23on
Experienced Contributor
7 replies

Do you know what it is, or what it is used for? This tool was made back in the 60's by a tradie to help him in his work as to buy one it would cost hi ...

JustJim
Budding Contributor
1 reply

So yesterday I used my assembly and outfeed table to build a surfboard. But it was a crappy surfboard, so today I turned it into a sheet goods and ...

JustJim
Budding Contributor

I was trying to sort out the layout for another tool mount for my tool wall but I didn't have enough flat space to lay out all the things I was trying ...

royq
Established Contributor
4 replies

Hi Workshoppers, I decided to post up some pics of my workbench build that I'm about halfway through, hoping to get some ideas for storage and a littl ...

Malcolm
Budding Contributor
6 replies
May

The framing got concreted in with quick set mix, propped up to get it nice and levelThe joins in the decking were randomised for strength.The shed was ...

r23on
Experienced Contributor
2 replies
May

Have you had an issue clamping materials and finding after the glue has dried, removing the clamps and your board were bowed. I know I have, no matter ...

pat2
New Contributor
6 replies

My Ryobi router is 4 years old..The spring collet got stuck...had it removed bought a new collet $46..now it is stuck first time using it.. Anyone he ...

Hansi
Junior Contributor
4 replies

Hi Guys... I have an old shed with a tin roof and I want to fix up some guttering. The tin roof overhangs quite a way and my plan was to fix up some s ...

Billy
Budding Contributor
5 replies

During levelling with a 'DYI' router/sled and levelling jigAfter.

Torrens85
New Contributor
4 replies

Just purchased a Tradeflame wood burner kit, was working fine until i changed the tip and now its not heating up at all Can anyone help? I'm not sure ...

Community Manager Jason
Community Manager
11 replies

I was having a chat to a friend recently about tools. His philosophy was that he was always happy to pay a little extra for quality so that the tool w ...

Community Manager Jason
Community Manager
20 replies

Here on Workshop we want to create an inclusive, welcoming community where anyone feels like they can seek help, including absolute beginners. After a ...